Hondabase

Community-Driven Honda Knowledgebase
Cars · Electronics

Proposed Datalogging & RTP Protocol

Technical specification of the proposed high-speed, stream-based custom datalogging and Real-Time Programming (RTP) protocol for Honda ECUs.

Advanced

Adapted from pgmfi.org wiki

This document defines the specification for a custom, stream-based serial communication protocol designed to replace the legacy polled serial interrupt handlers in Honda OBD0 and OBD1 ECUs.

The protocol aims to provide a cross-platform, high-efficiency connection that supports both high-speed datalogging and Real-Time Programming (RTP) emulation.

Core Design Principles

  1. Continuous Streaming (Non-Polling): Instead of the PC constantly requesting (polling) data, the ECU continuously streams standard datalogging packets at high speed. This minimizes serial latency and CPU overhead on the ECU.
  2. On-Demand Polling: While primary sensor telemetry streams continuously, the PC can inject short command packets to query arbitrary memory locations or ROM registers.
  3. Memory Space Querying: Supports reading any location within the 16-bit address space (RAM and ROM).
  4. Data Validation: Employs checksum verification and complement verification (CPL) on write operations to ensure communication integrity before writing to emulation memory (RTP).
  5. Bulk Writing: Supports a locked-interrupt bulk write mode for rapid ROM re-flashes.

Technical Workflow for Real-Time Programming (RTP)

To ensure that random serial glitches do not write corrupt values to running engine tables, a two-step validation write sequence is used:

  1. Data Transfer: The PC sends the payload (1 or 2 bytes) to the ECU using a Byte Write (0x10) or Word Write (0x11) packet.
  2. ECU Buffering: The ECU stores the data in a temporary memory buffer ("byte storage" or "word storage") and echoes a Destination Request packet (0xA0 / 0xA1) containing the received data back to the PC.
  3. Verification: The PC receives the destination request and verifies the echoed data matches what was sent.
  4. Execution:
    • If correct, the PC sends a Destination packet (0x20 / 0x21 / 0x22 / 0x23) specifying the final target memory address.
    • Upon receiving the destination packet, the ECU moves the buffered data to the final target address in RAM/ROM space.
    • If the verification fails, the PC discards the buffer and restarts from Step 1.

PC-to-ECU Command Packets

Packets sent from the PC to the ECU consist of 5 bytes. A checksum byte is calculated as the 8-bit sum of the address or data bytes.

Command Name Byte 1 (ID) Byte 2 Byte 3 Byte 4 Byte 5 Function & Reply Behavior
Byte RAM Read 0x02 Addr (Hi) Addr (Lo) CS 0x02 Reads a byte from RAM. Replies with 0x82 packet.
Word RAM Read 0x03 Addr (Hi) Addr (Lo) CS 0x03 Reads a word from RAM. Replies with 0x83 packet.
Byte ROM Read 0x04 Addr (Hi) Addr (Lo) CS 0x04 Reads a byte from ROM. Replies with 0x84 packet.
Word ROM Read 0x05 Addr (Hi) Addr (Lo) CS 0x05 Reads a word from ROM. Replies with 0x85 packet.
Byte Write 0x10 Data CPL Data CS 0x10 Sends a RAM byte to temporary storage. Replies with 0xA0.
Word Write 0x11 Data 1 Data 2 CS 0x11 Sends a RAM word to temporary storage. Replies with 0xA1.
8-bit RAM Dest 0x20 Addr Addr CS 0x20 Writes buffered byte to an 8-bit RAM address.
16-bit RAM Dest 0x21 Addr (Hi) Addr (Lo) CS 0x21 Writes buffered byte to a 16-bit RAM address.
16-bit ROM Dest 0x22 Addr (Hi) Addr (Lo) CS 0x22 Writes buffered byte to a 16-bit ROM address (RTP).
16-bit ROM Word Dest 0x23 Addr (Hi) Addr (Lo) CS 0x23 Writes buffered word to a 16-bit ROM address (RTP).
Bulk Write Address 0x80 Addr (Hi) Addr (Lo) 0x00 0x80 Sets data pointer and locks ECU in serial interrupt.
Bulk Write Start 0x81 Length Data... - - Writes Length bytes to ROM starting at data pointer.

Note: CS is the 8-bit checksum byte, and CPL is the bitwise complement (~).

ECU-to-PC Reply Packets

ECU reply packets are 5 bytes long, with the first byte acting as the packet type identifier.

Packet Type Byte 1 (ID) Byte 2 Byte 3 Byte 4 Byte 5 Description / Payload
Continuous Telemetry 0x01–0x7F Data 1 Data 2 Data 3 CS Real-time streaming sensor values.
Bulk Write Addr Reply 0x80 Addr (Hi) Addr (Lo) 0x00 0x00 Confirms the target bulk write address.
Bulk Write Verification 0x81 CS 0x00 0x00 0x00 Confirms the integrity of the bulk-written block.
Read RAM Byte Reply 0x82 Data CPL Data Data CS Returns the requested 8-bit RAM value.
Read RAM Word Reply 0x83 Data 1 Data 2 CS (D1) CS (D2) Returns the requested 16-bit RAM value.
Read ROM Byte Reply 0x84 Data CPL Data Data CS Returns the requested 8-bit ROM value.
Read ROM Word Reply 0x85 Data 1 Data 2 CS (D1) CS (D2) Returns the requested 16-bit ROM value.
Byte Dest Request 0xA0 Data CPL Data CS Data Confirms byte is held in buffer, awaiting destination.
Word Dest Request 0xA1 Data 1 Data 2 CS (D1) CS (D2) Confirms word is held in buffer, awaiting destination.
Negative Ack (NAK) 0xFF 0x00 0xFF 0x00 0xFF Sent if an invalid or corrupt packet is received.

Credits and source

Authors blundar

Source Adapted from Proposed Datalogging Protocol on pgmfi.org wiki. Licensed under CC BY-NC-SA 1.0.